 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Document: SP0102N Last Revision Date: 09-2003 Product Specification: SP0102 Series (Generation II) This document applies the following SiSonic Model Numbers: SP0102NC3-2 SP0102NC3-3 SiSonic microphone was developed as a cost effective alternative to traditional electret condenser microphones. Provided on tape-and-reel, SiSonic is ideally suited for high volume applications. It can be processed directly to a customer's PCB using standard automatic pick-and-place equipment, and surface mounted via standard solder reflow equipment. Microphone Dimensional Layout Item Height Length Width Weight Coplanarity Dim. 1.45 6.15 3.76 < 0.5 < 0.1 Tol. (+/-) 0.15 0.05 0.05 Units mm mm mm grams mm Microphone Pin Output Recommended PCB Land Layout Knowles Acoustics www.knowlesacoustics.com 1 Document: SP0102N Last Revision Date: 09-2003 Product Specifications Test Conditions: +20C, 60-70% R.H. Limits Symbol Directivity Sensitivity Output impedance Current Consumption Signal to Noise Ratio Typical Input Referred Noise Supply Voltage Sensitivity Loss across Voltage Maximum Input Sound Level S ZOUT IDSS S/N ENL Vs Change in sensitivity over 5.5v to 1.5v Condition Omni-directional @ 1kHz (0dB=1V/Pa) @ 1kHz (0dB=1V/Pa) across 1.5 to 5.5 volts @ 1kHz (0dB=1V/Pa) A-weighted 1.5 0.100 55 59 35 5.5 -46 -42 -38 100 0.250 dB mA dB dBA SPL Min. Nom. Max. Unit V dB dB No Change Across Voltage Range At 100dB SPL, THD < 1% At 115dB SPL, THD = < 10% -40 -40 100 - 10,000 +100 +100 Operating Temperature Storage Temperature Frequency Range C C Hz Frequency Response Curve Knowles Acoustics www.knowlesacoustics.com 2 Document: SP0102N Last Revision Date: 09-2003 Packaging Specifications Carrier - Tape Detail Model Number SP0102NC3 SP0102NC3 Suffix Reel Diameter 7" 13" Qty per Reel 1,200 4,500 Capacitor Config. 10 & 33pF 10 & 33pF Tape & Reel Leader Length Label Available in 7" or 13" diameter. 800mm or minimum of 100 empty pockets Label applied to external package and direct to reel. Per JEDEC. 1 year storage (original packaging, low humidity) "L" - direction -2 -3 NOTE: All devices are lead-free, and compatible with leadfree reflow profile. Storage Life Polarity of part Solderability Characteristics Solder Reflow Terminal Pads # of Reflow Passes Reflow Profile (Maximum Conditions) (** No board washing after reflow **) 260C for maximum 30 seconds Gold (27u") over Nickel (150u") Typical reference Reliability section Knowles Acoustics www.knowlesacoustics.com 3 Document: SP0102N Last Revision Date: 09-2003 Reliability Thermal Shock High Temperature Storage Test Low Temperature Storage Test High Temperature Operating Test Low Temperature Operating Test Humidity Test Vibration Test Microphone unit must operate when exposed to air-to-air thermal shock 100 cycles, from -40C to +125C. (IEC 68-2-4), Microphone unit must maintain sensitivity after storage at +105C for 1,000 hours. (IEC 68-2-2 Test Ba) Microphone unit must maintain sensitivity after storage at -40C for 1,000 hours. (IEC 68-2-1 Test Aa) Microphone unit must operate within sensitivity specifications for 16 hours at 105C. (IEC 68-2-2 Test Ba) Microphone unit must operate within sensitivity specifications for 16 hours at -40C. (IEC 68-2-1 Test Aa) Tested under Bias at 85C/85% R.H. for 270 hours. (JESD22-A101A-B) Microphone unit must operate under test condition: 4 cycles, from 20 to 2,000 Hz in each direction (x,y,z), 48 minutes, using peak acceleration of 20g (+20%, -0%). (MIL 883E, method 2007.2, A) Tested to 8kV direct contact discharge or 15kV air discharge as specified by IEC 1000-4-2, level 3 and level 4. Microphone is tested to 5 passes through reflow oven, with microphone mounted upside-down under conditions of 260C for 30 seconds maximum. Tested to greater than 5,000g (IEC 68-2-27, Ea). After test conditions are performed, the sensitivity of the microphone shall not deviate more than 3dB from its initial value. Electrostatic Discharge Reflow Mechanical Shock Note: Dotted Section Represents SiSonic Microphone Recommended Interface Circuit + Term. 4 * * R1 * Term. 1 R2 + External Gain (set by customer) = -R1/R2 Term. 3 Vref Knowles Acoustics www.knowlesacoustics.com 4 |
Price & Availability of SP0102NC3-2
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |